"MY CARBURETOR OVERFLOATS"

1. Restricted fuel tank vent
system.
2. Loose float bowl screws- When your carburetors bowl screws are loosed it allows fuel to drop from the port, sometimes it could be due to a worn out bolt or threading in carburetor.
3. Damaged float bowl O-ring- a damaged rubber seal/o-ring could also cause fuel leakage, since it can't seal the space no longer
4. Damaged or leaking float
assembly- a float assembly include the jet and the float. Dismantle the float assembly and make sure that the fuel inlet is not blocked
5. Particle contamination in fuel
inlet fitting cavity-using a carburetor cleaner; soak carburetor in it for at least 30 minutes then couple..
6. Worn or dirty inlet valve or seat- bad valves and seats could also cause this, in two stroke generators(small gen), the carburetor seats directly on the valve. You can loosen the valve at the back of the valve, therer ar two screws loosen them clean valve wit petrol them couple back and tighten the carb
7. Improper fuel level in float bowl- change the float

Comments

Post a Comment

Popular posts from this blog

HOW TO SERVICE YOUR SMALL GENERATOR CARBURETOR

HOW TO SERVICE YOUR CARBURETOR!!!   Local generator repairers get about 60% of their income frrom just changing or servicing the carburetor. This DIY will not only save you money but also workshop labour. Now i'm guessing you've tried to srart your generator at this point and it's not responding or it shoots and goes back off, now go to the steps below......... STEP 1: DISMANTLING THE CARBURETOR firstly loosen the tank so you'll get enough space. then loosen the cover covering the carburetor(for small gens). Then you get the carburetor's bolts, loosen them also, move the board forwad so you can get to your carburetor. Unlock the throttle cable from the carburetor linkage. 2: Place it in a container to catch the fuel coming out, open the carburetor from bottom(you'll see a short bolt) loosen the bolt & remove the bowl. check for corrosion if there's corrosion you'll probably be needing a sandpaper to scratch of the corrosion and make the bowl
Read more

Explanation of a small petrol generator (Parts)

Image
on my previous post, i talked about how a petrol generator works and i also did some explanations on the main components.Now lets move on to how a small petrol generator works....                     SMALL GENERATOR All generators works with a process called internal combustion, it consists of different parts: Piston   A piston is a component of reciprocating engines, reciprocating pumps, gas compressors and pneumatic cylinders, among other similar mechanisms. It is the moving component that is contained by a cylinder and is made gas-tight by piston rings. Rings    A piston ring is a split ring that fits into a groove on the outer diameter of a piston in a reciprocating engine such as an internal combustion engine or steam engine. Spark plug     It is a device for delivering electric current from an ignition system to the combustion chamber of a spark -ignition engine to ignite the compressed fuel/air mixture by an electric spark Cylinder A cylinder is t
Read more

"HOW TO REMOVE CARBON PILE UPS FROM EXHAUST PORT AND MUFFLER"

Exhaust port is a passage through which the burnt mixture is passed out from the combustion chamber. it is located differently in different engine cyles. In a two stroke generator it is underneath the engine block while in a four stroke generator it is located on the left hand part of the cylinder. The exhaust muffler is connected to the port to reduce the sound from the generator and also to expel the harmful gas coming out from the engine. Mostly in two stroke engines; carbon usually piles up both at the exhaust port and inside the muffler thereby causing low RPM. In power generators this brings about low current. Removing carbon deposits is easy with this easy to follow steps: 1) loosen the exhaust from the exhaust port 2) get a long screw driver and drive it into the exhaust port, clean all carbon deposits from the port 3) use the screw driver to also clean the muffler through the hole..i usually pour in a little fuel in my muffler and light it up so it could dry up the carbon
Read more