SPARK PLUG

                                                     SPARK PLUG

I've been asked alot of questions about generators in the my few years of being in the field, but one common question is the question of "hard starting"...well , hard starting in a generator both big and small can occur due to different reasons. I'm saying that not one particular component can cause it!! one common factor of hard starting is the PLUG. When the plug is bad or filled with lots of carbon, it can cause hardstarting.
 HOW TO CLEAN OR REPLACE
get your plug spanner, you can get one in any mechanical store.. Fit it in the plug then rotate or loosen in an anti clockwise way, when it's out clean with a needle or something tiny that can go into the plugs space. insert back into the cylinder and tighten in a clock wise way...this can also be applied when changing and replacing with a new plug..

Comments

  1. Ukasgroup30 June 2016 at 08:17

    Wow, this post has been of great help, keep it coming bro

    ReplyDelete

Post a Comment

Popular posts from this blog

HOW TO SERVICE YOUR SMALL GENERATOR CARBURETOR

HOW TO SERVICE YOUR CARBURETOR!!!   Local generator repairers get about 60% of their income frrom just changing or servicing the carburetor. This DIY will not only save you money but also workshop labour. Now i'm guessing you've tried to srart your generator at this point and it's not responding or it shoots and goes back off, now go to the steps below......... STEP 1: DISMANTLING THE CARBURETOR firstly loosen the tank so you'll get enough space. then loosen the cover covering the carburetor(for small gens). Then you get the carburetor's bolts, loosen them also, move the board forwad so you can get to your carburetor. Unlock the throttle cable from the carburetor linkage. 2: Place it in a container to catch the fuel coming out, open the carburetor from bottom(you'll see a short bolt) loosen the bolt & remove the bowl. check for corrosion if there's corrosion you'll probably be needing a sandpaper to scratch of the corrosion and make the bowl...
Read more

"HOW TO REMOVE CARBON PILE UPS FROM EXHAUST PORT AND MUFFLER"

Exhaust port is a passage through which the burnt mixture is passed out from the combustion chamber. it is located differently in different engine cyles. In a two stroke generator it is underneath the engine block while in a four stroke generator it is located on the left hand part of the cylinder. The exhaust muffler is connected to the port to reduce the sound from the generator and also to expel the harmful gas coming out from the engine. Mostly in two stroke engines; carbon usually piles up both at the exhaust port and inside the muffler thereby causing low RPM. In power generators this brings about low current. Removing carbon deposits is easy with this easy to follow steps: 1) loosen the exhaust from the exhaust port 2) get a long screw driver and drive it into the exhaust port, clean all carbon deposits from the port 3) use the screw driver to also clean the muffler through the hole..i usually pour in a little fuel in my muffler and light it up so it could dry up the carbon...
Read more

"VALVE ADJUSTMENT & REPAIRS"

Image
Valves controls the flow of fuel vapour in the combustion chamber and the flow of exhaust gasses leaving the engine. faulty or dirty valves may stick & can develop pits, cracks, & grooves that can cause the engine to loose power and fuel efficiency. if you are having problems with your engine or you just want to do an overall valve maintainance, go with the steps below.. HOW TO REMOVE SMALL ENGINES VALVES FOR INSPECTION in order to properly inspect your valve, you have to remove them....  NOTE: wear saftey eye wears when removing your valve... STEP 1: remove the spark plug and secure the spark plug lead away from the spark plug. STEP 2: remove air cleaner assembly, fuel tank , oil fill tube, blower housing, carburetor and any other engine parts that blocks access to the cylinder head  STEP 3: remove muffler/exhaust from the cylinder, cranck case breather and any other that blocks access to valve chamber STEP 4: open cylinder cover   ,remove ...
Read more